English English

Find Products By Models

XLED95 with ratio 99 121 187 289 391 493 595 731 841 1003 1225 1505 1849 2065 2537 3481 4189 5133 7569

XLED95 with ratio 99 121 187 289 391 493 595 731 841 1003 1225 1505 1849 2065 2537 3481 4189 5133 7569

XLED95-99-11 XLED95-121-7.5 XLED95-187-7.5 XLED95-289-5.64 XLED95-391-4.19 XLED95-493-3.32 XLED95-595-2.75 XLED95-731-2.24 XLED95-841-1.95 XLED95-1003-1.62 XLED95-1225-1.33 XLED95-1505-1.08 XLED95-1849-0.88 XLED95-2065-0.79 XLED95-2537-0.64 XLED95-3481-0.47 XLED95-4189-0.39 XLED95-5133-0.31 XLED95-7569-0.21

WD cylindrical worm reducer The standard is Arc himedes cylindrical worm reducer with one-stage transmission; WS (worm mounted on top) and WD (worm mounted on bottom). (The worm Archimedes cylindrical worm reducer is suitable for the sliding speed of the worm meshing part not to exceed 7.5m/s; the worm speed does not exceed 1500r/min; the working environment temperature is -40~+40℃; and it can run in the forward and reverse directions. occasion.
WD worm reducer model mark
Model mark
The markings of the cylindrical worm reducer include: model, center distance, transmission ratio, assembly type.

BWED

Cycloidal pin gear reducer is a novel transmission device that applies the principle of planetary transmission and adopts the meshing of cycloidal pin teeth. The entire transmission device of the cycloid reducer can be divided into three parts: input part, deceleration part, and output part. A double eccentric sleeve with a displacement of 180° is installed on the input shaft, and two roller bearings called swing arms are installed on the eccentric sleeve to form the H mechanism. The center holes of the two cycloids are the upper swing arm bearings of the eccentric sleeve. In order to reduce the friction, in a reducer with a small speed ratio, the cycloidal wheel meshes with a set of circularly arranged needle teeth on the needle gear to form an internal meshing reduction mechanism with a tooth difference of one tooth. , Needle tooth sleeve is attached to the needle tooth).

Features:
It can achieve a high reduction ratio of 1:87 and a high-efficiency single-stage transmission of more than 90%. If a multi-stage transmission is used, the reduction ratio will be greater. The reduction ratio of the first-stage transmission is 9~87, the reduction ratio of the two-stage transmission is 121~5133, and the multi-stage combination can reach tens of thousands. And the pin-tooth engagement system sleeve type rolling friction, the meshing surface has no relative sliding, so the first-stage reduction efficiency is up to 94%. Compact structure and small size. Due to the planetary transmission principle, the input shaft and output shaft are on the same axis, so that the size of the model can be as small as possible. Smooth running and low noise. Cycloid needle teeth have a large number of meshing teeth, a large overlap coefficient and a mechanism of mechanical balance, so that vibration and noise are restricted to a minimum. During operation, there are many pairs of teeth in contact at the same time, with large coincidence, stable operation, strong overload capacity, low vibration and noise, and low noise for models of various specifications. Reliable use and long life. Because the main parts are made of bearing steel material, high strength is obtained by quenching (HRC58-62), and part of the transmission contact uses rolling friction, so it is durable and has a long life. Because the main parts are made of bearing steel quenching treatment (HRC58-62), and then finely ground, and the cycloidal teeth and the needle gear sleeve are meshed and transmitted to the needle teeth to form a rolling friction pair, the friction coefficient is small, so that there is no relative sliding in the meshing area. Very little wear and tear, so it is durable. Reasonable design, convenient maintenance, easy disassembly and installation, minimum number of parts and simple lubrication make the cycloid reducer deeply trusted by users. Compared with other reducers of the same power, the weight and volume are more than 1/3 smaller. Due to the planetary transmission, the input shaft and output shaft are on the same axis to obtain the smallest possible size.

use:
Cycloidal pin gear reducer adopts the principle of cycloidal pin tooth meshing and planetary transmission, so it is usually called planet cycloid reducer. Planetary cycloid pin gear reducer can be widely used in petroleum, environmental protection, chemical industry, cement, transportation, In textile, pharmaceutical, food, printing, lifting, mining, metallurgy, construction, power generation and other industries, as a drive or reduction device, the machine is divided into horizontal, vertical, double-shaft and direct-connected assembly methods. Its unique and stable structure can replace ordinary cylindrical gear reducers and worm gear reducers in many cases. Therefore, planetary cycloid reducers are widely used in various industries and fields and are generally welcomed by users.

BWED10 493

First, the characteristics of BWED cycloid reducer, BWED cycloid reducer:
According to JB/T2982-94, a new type of transmission machine designed by the principle of planetary transmission with less tooth difference and cycloidal needle gear meshing. It has been widely used in petrochemical industry, construction, metallurgical mines, lifting and transportation, textile printing and dyeing, Construction machinery, food industry, electronic television and other fields are deeply trusted and praised by users.
Cycloidal pinwheel reducer has the following characteristics:
1. Large transmission ratio: the single-stage transmission ratio is 9-87. The two-stage transmission ratio is 99-7569, and the transmission ratio can be larger when multiple stages are connected in series;
2. High transmission efficiency: single-stage transmission efficiency is above 90%;
3. Compact structure: small size, light weight, high-speed shaft and low-speed shaft on the same axis, easy assembly and disassembly;
4. Smooth operation, low noise, can withstand overload and impact;
5. Reliable use and long life.


Second, the model and specifications of the BWED cycloid reducer
Type:
BW cycloidal pinwheel reducer is foot plate type, double shaft type, horizontal installation;
BL cycloid reducer is flange type, double shaft type, vertical installation;
BWY cycloidal pinwheel reducer is a foot plate type, dedicated asynchronous motor direct connection type, horizontal installation; BLY cycloidal pinwheel reducer is a flange type, special asynchronous motor direct connection type, vertical installation; BWD foot plate type horizontal installation Ordinary motor direct-coupled cycloid reducer;
BLD flange type vertical mounted ordinary motor direct-coupled cycloid pinwheel reducer.
Third, the BWED cycloid reducer, the use and lubrication instructions of the BWED cycloid reducer
(1) Use:
1. This machine is suitable for continuous work, allowing forward and reverse operation;
2. The rotation of the output shaft of the single-stage reducer is opposite to that of the input shaft, and the rotation of the output shaft of the double-stage reducer is the same as that of the input shaft. The rotation of the output shaft of the three-stage reducer is opposite to that of the input shaft;
3. The output shaft of this reducer cannot bear axial force;

BWED31 4934. When the output shaft and input shaft are matched with other parts, direct hammering is not allowed to prevent damage;
5. The keys on the shaft extension of the output shaft and the input shaft are selected according to the regulations of the ordinary flat key type ruler (GB1096-79), and the fit tolerance value of the stop diameter D4 of the output end of the vertical reducer meets the limit and fit (GB1801-99) H9 regulations;
6. When using a coupling, the working machine and the motor should be connected with the axis concentric, and the installation error of the reducer should not be greater than the allowable error value of the coupling used;
7. The reducer can be turned flexibly by hand after installation;
8. Horizontal dual-shaft reducers generally work in a horizontal position with the axis of the output shaft; the elevation angle of the axis should not exceed 15 degrees when it must be used inclined (the end of the output shaft extends downward);
9. The vertical reducer should be used vertically downward at the end of the output shaft;
10. After installation, the reducer must be tested and run before it is put into use. Under normal idling conditions, load and run gradually;
11. When the load is large, the base and foundation should be equipped with positioning pins or optional hydraulic couplings when starting frequently.
(2) Lubrication:
1. This machine is mainly oil bath lubrication
Suitable for ambient temperature: -10 degrees Celsius to 40 degrees Celsius: N46, N68 lubricating oil is available when ambient temperature is -10 degrees Celsius to 0 degrees Celsius; N68, N100, N150, N220 lubricating oil is used at 0 degrees Celsius to 40 degrees Celsius, and can be used when tilted installation Grease lubrication, vertical type BL27 and XL7 and above have circulating lubrication: start the oil pump micro-motor before driving, depending on whether the oil pump is supplying oil, otherwise, the micro-motor wiring should be inverted, because the oil pump runs in the specified direction and the oil pump is in normal operation Afterwards, the height of the oil level should be kept at the center line of the circular oil mark, and the oil pump and the end face of the reducer should have an "O" seal ring to prevent oil leakage and leakage.
2. Oil change system
After the first refueling operation for two weeks, new oil should be replaced and the internal oil should be flushed out. It can be replaced every 3-6 months in the future. If the ambient temperature is high and humid, the oil change time should be shortened appropriately. The oil storage in the reducer body must maintain the specified oil level during operation, and it should not be too much or too little. Rotate the breather cap on the base or flange to add oil.

BWED20 493

Product features and technical specifications of X series cycloid reducer:
The planetary cycloidal reducer is a reduction mechanism with advanced design and novel structure, applying the principle of planetary transmission, adopting the meshing of cycloidal pinwheels. This type of reducer has replaced two-stage and three-stage ordinary cylindrical gear reducers and cylindrical worm reducers in most cases. It is used in military, aerospace, metallurgy, mining, petroleum, chemical, shipbuilding, light industry, food, textile, Printing and dyeing, pharmacy, rubber, plastics, and lifting and transportation have been widely used.
First, the features of cycloid reducer
1. The transmission ratio is large. The transmission ratio is 1/6-1/87 in the first deceleration. The transmission ratio in the two-stage reduction is 1/99--1/7569; in the three-stage transmission, the transmission ratio is 1/5841-1/658503. In addition, multi-stage combination can be used according to needs, and the speed ratio can reach the specified value.
2. High transmission efficiency. Because the meshing part adopts rolling meshing, the general first-level transmission efficiency is 90%-95%.
3. Compact structure, small size and light weight. Compared with ordinary cylindrical gear reducer, the volume can be reduced by 2/1-2/3.
4. Fewer failures and long life. The main transmission engaging parts are made by grinding bearing steel, so the mechanical properties and wear resistance are good, and because it is rolling friction, there are few failures and long life.
5. Smooth and reliable operation. Due to the multi-tooth meshing during the transmission process, the operation is stable and reliable, and the noise is low.
6. Convenient disassembly and assembly, and easy maintenance.
7. Strong overload capacity, impact resistance, small moment of inertia, suitable for frequent starting and forward and reverse rotation.
Second, the technical specifications of cycloid reducer
1 Machine model:
According to the transmission ratio, it is divided into: first, second and third.
There are thirteen types at the first level: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12.
There are 14 models in two levels: 00, 20; 32, 42, 53, 63, 64, 74, 84, 85, 95, 106, 117, 128.
There are 8 models for the third level: 420, 742, 842, 853, 953, 1063, 1174, 1285.
According to the structure type, it is divided into four types: horizontal, vertical, double-shaft, and direct-coupled.
2. Transmission ratio:
The transmission ratios of the first reduction are: 9, 11, 17, 21, 23, 25, 29, 35, 43, 47, 59, 71, 87.
The two-stage reduction gear ratios are: 99, 121, 187, 289, 319, 385, 473, 493, 595, 649, 731, 841, 1003, 1225, 1505, 1849, 2065, 2537, 3045, 3481, 5133.
The transmission ratio of the three-stage reduction is: 5841-658530

BWED20 1505 0.07

Brief Introduction:
When the input shaft rotates with the eccentric sleeve for one cycle, due to the characteristics of the upper tooth profile curve of the cycloidal wheel and the limitation of the needle gear on the needle gear, the motion of the cycloidal wheel becomes a plane motion with both revolution and rotation. When the input shaft rotates forward for one cycle, the eccentric sleeve also rotates one cycle, and the cycloidal wheel rotates one tooth in the opposite direction to obtain deceleration. Then, with the help of the W output mechanism, the low-speed rotation motion of the cycloidal wheel is transmitted to the output shaft through the pin shaft. In order to obtain a lower output speed.

NER GROUP CO.,LIMITED is a professional manufacturer and exporter of gearbox reducers, gear motors and electric motors for several years from China.
We believe that we can cooperate with you on this business and please contact us if you are interested.
You are welcomed to visit our catalogue website for more information:
www.sogears.com
Mobile:+86-18563806647
www.guomaodrive.com
https://twitter.com/gearboxmotor
Viber/Line/Whatsapp/Wechat: 008618563806647
E-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.; Skype ID: qingdao411
No.5 Wanshoushan Road, Yantai, Shandong,China(264006)
Gear reduction motor, reduction gearbox manufacturer, visit www.bonwaygroup.com Email: This email address is being protected from spambots. You need JavaScript enabled to view it. WhatsApp: +86-18563806647

PDF Catalogue

 

Inline helical gear reducer

Helical gear, Helical Gear Motors

Gear motor for sale

Bevel gear, Bevel gear motor, Helical gear, Helical Gear Motors, Spiral bevel gear , Spiral Bevel Gear Motor

Offset gear motor

Helical gear, Helical Gear Motors

Helical worm gear motor sew

Helical gear, Helical Gear Motors, Worm gear, Worm gear motor

Flender type gearboxes

Bevel gear, Helical gear

Cycloidal drive

Cycloidal gear , Cycloidal Gear Motor

Types of electric motor

AC Motor, Induction Motor

Mechanical variable speed drive

Cycloidal gear , Cycloidal Gear Motor, Helical gear, Planetary gear, Planetary gear motor, Spiral Bevel Gear Motor, Worm gear, Worm Gear Motors

Types of gearbox with images

Bevel gear, Helical gear, Spiral bevel gear

Electric motor and gearbox combination

Cycloidal gear , Cycloidal Gear Motor

Sumitomo type cyclo

Cycloidal gear , Cycloidal Gear Motor

Skew Bevel Gear Box

Bevel gear, Spiral bevel gear

 Geared Motors And Electric Motor Manufacturer

The best service from our transmission drive expert to your inbox directly.

Get in Touch

Yantai Bonway Manufacturer Co.ltd

ANo.160 Changjiang Road, Yantai, Shandong, China(264006)

T+86 535 6330966

W+86 185 63806647

© 2024 Sogears. All Rights Reserved.