Yantai Bonway Manufacturer

Worm gearbox for electric motor

worm gearbox for electric motor, right angle Worm gearbox for electric motor, worm gear sets catalog, worm gear reduction box, worm gear box, worm gearbox, Best Selling WPA Series Worm Speed Gear Reducers, worm reduction gearbox, WP Series Worm Gear Box Input shaft with flange mounting

WP Worm gearbox for electric motor in stock is developed on the basis of WD Worm gearbox for electric motor. The worm is made of 45# high-quality steel by heat treatment. The worm wheel is made of tin bronze. The wear resistance is good, especially in the bearing capacity. The Worm gearbox for electric motor in stockr is mainly used for the reduction transmission of various mechanical equipments such as plastics, metallurgy, beverages, mining, lifting and transportation, and chemical construction.

New Right Angle worm gearbox for electric motor For Sale sogears brand is a worm gearbox for electric motor wholesale supplier. Our right angle Worm gearbox for electric motor inventory includes worm gearbox for electric motor in a number of standard configurations, with a wide range of available ratios to provide maximum efficiency.

Worm gearbox for electric motor

According to the shaft output of WPDA Worm gearbox for electric motor, there are six directions of R, L, V, W1, W2 and
F (please refer to the installation dimension specification table for details), using imported bearings, oil
seals and lubricating oil, and the worm wheel is made of aluminum bronze. Seiko manufacturing, greatly
improving the service life of Worm gearbox for electric motor, running quite smoothly, no noise, no vibration, high transmission
efficiency and so on.
After the assembly test of the Worm gearbox for electric motor is passed, the no-load test (test run) is usually carried out. The
test run should be carried out at the rated number of revolutions or the number of high-axis revolutions
(500-1500 r/min). During the test, sufficient oil should be injected according to the oil level indicated by
the oil gauge. The test time is recommended to be 1 hour. At the same time as the test run time is reached,
it is additionally required to check whether the following requirements are met:

1. The connecting parts and fasteners must not have any looseness;

2. There shall be no oil leakage or oil leakage at each seal or joint;

3. The operation of Worm gearbox for electric motor should be stable and normal, and there must be no impact or vibration;

4. The surface temperature of Worm gearbox for electric motor should be in the normal range;

5. For the continuous working Worm gearbox for electric motor, the load test must be carried out under the condition of rated load
rotation for not less than 2 hours, the temperature of the lubricating oil should not be higher than 35 °C,
and the temperature rise of the bearing should not be higher than 40 °C.

For industry applications that demand reliable speed reduction at a high energy efficiency, worm gearbox for electric motor from sogears offer a perfect solution. We carry worm gearbox for electric motor products in double reduction, single reduction and worm-helical types for versatile functionality, good performance.

Performance characteristics:The transmission is stable, the vibration, impact and noise are small, the reduction ratio is large, the versatility is wide, and it can be used with various mechanical equipments.can get a larger transmission ratio with a single-stage transmission, compact structure, most models of Worm gearbox for electric motor have better self-locking, can save the brake device for mechanical equipment with braking requirementsThe meshing friction loss of the worm screw tooth and the worm gear tooth surface is large, so the transmission efficiency is lower than the gear, easy to heat and high temperature.Higher requirements for lubrication and cooling.

5, good interoperability, worm gears are manufactured according to national standards, bearings, oil seals, etc. are used standard parts.

6, the box type has a basic type (the box is a vertical or horizontal structure with a foot plate) and a universal type (the box is a rectangular parallelepiped, with multiple fixed holes, no bottom plate or another bottom) Various types of structure such as foot board)

There are two basic types of input shaft connection (single input shaft and double input shaft) and two types of motor flanges.The output and input shafts have the input shaft at the bottom and the top; the output shaft is up and down; the input shaft is up and down.Two or three Worm gearbox for electric motors can be used to form a multi-stage Worm gearbox for electric motor to obtain a great gear ratio.

Precautions
1. The transmission is stable, the vibration, the impact and the noise are small, the reduction ratio is
large, the versatility is wide, and it can be used with various mechanical equipments.
2. The meshing friction loss of the worm screw tooth and the worm gear tooth surface is large, so the transmission efficiency is lower than the gear, and it is easy to generate heat and high temperature.
3. Higher requirements for lubrication and cooling.
4. It can obtain a large transmission ratio with single-stage transmission, and has a compact structure. Most models have better self-locking performance, and can save braking devices for mechanical equipment with braking requirements.
5. The box type has a basic type (the box is a vertical or horizontal structure with a foot board) and a universal type (the box body is a rectangular parallelepiped, and the multi-faceted fixed screw holes are provided without a foot plate or an additional bottom. Various types of structure such as foot board)
6. WP cast iron Worm gearbox for electric motor input shaft connection has basic type (single input shaft and double input shaft), with motor flange.
7. Output and input shaft position direction has input shaft on and under; output shaft up and down; input shaft up and down.
8. Mutual compatibility is good, worm gears are manufactured according to national standards, and standard parts are used for bearings and oil seals.
9. Two or three Worm gearbox for electric motors can be used to form a multi-stage Worm gearbox for electric motor to obtain a great gear ratio

Good prices for worm gearbox for electric motors, industrial surplus suppliers, gearmotors for sale, speed Worm gearbox for electric motors for sale, gear Worm gearbox for electric motors for sale, industrial ac gearmotors, gearboxes suppliers. Right Angle worm gearbox for electric motor and Our high-quality right angle gearboxes and speed Worm gearbox for electric motors have nylon or bronze worm gears, solid or hollow shafts, and are manufactured for a wide spectrum of applications.

Showcasing WP series worm gearbox for electric motor and other relevant items available for sale by email and Featuring Worm gearbox for electric motor in stock right now.

WP series worm gearbox for electric motor: with Double Reduction or single. Double Reduction worm gearbox for electric motor Product Configuration . IPTS, Inc. manufacturers double reduction Worm gearbox for electric motors that are built to last. Double reduction WP series worm gearbox for electric motorare made with the same high quality components as the single reduction WP series worm gearbox for electric motor.

The Worm gearbox for electric motor has the following advantages:
1. Strong hardness and excellent heat dissipation performance.
2, easy to install and maintain.
3. The product has high precision, stable operation, quiet and no vibration.
4. High safety and reliability and long service life.
5, factory direct sales, complete model specifications, stock.
6.The structure of the box is integral, the appearance is beautiful and the rigidity is good
Product Details
First, WP casting Worm gearbox for electric motor overview:
    WP Worm gearbox for electric motor is developed on the basis of wd Worm gearbox for electric motor. The worm is made of 45# high-quality
steel by heat treatment. The worm wheel is made of tin bronze. The wear resistance is good, especially in t
he bearing capacity. It is mainly used for the reduction transmission of various mechanical equipment such
as plastics, metallurgy, beverages, mining, lifting and transportation, and chemical construction.
Second, WP cast iron Worm gearbox for electric motor features:
    1. The transmission is stable, the vibration, impact and noise are small, the reduction ratio is large, the
versatility is wide, and it can be used with various mechanical equipments.
    2. It can obtain a large transmission ratio with single-stage transmission, and has a compact structure.
Most models have better self-locking performance, and can save braking devices for mechanical equipment
with braking requirements.
    3. The meshing friction loss of the worm screw tooth and the worm gear tooth surface is large, so the
transmission efficiency is lower than the gear, easy to heat and high temperature.
    4. Higher requirements for lubrication and cooling.
    5, good interoperability, worm gears are manufactured according to national standards, bearings, oil
seals, etc. are used standard parts.
    6, the box type has a basic type (the box is a vertical or horizontal structure with a foot plate) and a
universal type (the box is a rectangular parallelepiped, with multiple fixed holes, no bottom plate or another
bottom) Various types of structure such as foot board)
    7. There are two basic types of input shaft connection (single input shaft and double input shaft) and two
types of motor flanges.
    8. The output and input shafts have the input shaft at the bottom and the top; the output shaft is up and
down; the input shaft is up and down.
    9. Two or three Worm gearbox for electric motors can be used to form a multi-stage Worm gearbox for electric motor to obtain a great gear ratio.

Third, WP cast iron Worm gearbox for electric motor working conditions: 1. The worm speed of the Worm gearbox for electric motor cannot exceed 1500r/min. 2. The working environment temperature is -40 °C - +40 °C. When the working environment temperature
is lower than 0 °C, the lubricating oil must be heated to above 0 °C before starting. When the working environment
temperature is higher than 40 °C, cooling measures must be taken. 3. The Worm gearbox for electric motor can be rotated in the positive and negative directions. Fourth, note: 1. The worm gear shaft can never be used as an input shaft. 2. The supporting motor (ie power) cannot exceed the value specified on the label. 3. If the user wants to change the direction of the input shaft, the lower end cover of the lower shaft can
be removed, the worm shaft can be taken out and the 180 can be adjusted. Just load it. Do not hard knock
when installed, slowly drive the two shafts to make them engage.
This series is designed and manufactured according to the international Q/MD1-2000 technical quality standard.
Because this series of products adopts new technology and new material production, the performance of
the whole machine is better than that of foreign products of the same type. Worm gearbox for electric motor has a unique shape
and structure. The box is beautiful in appearance and made of high quality materials.
Well received by users, it is the best choice for modern industrial equipment to achieve high torque, large
speed ratio, low noise, high stability mechanical reduction transmission control device. The Worm gearbox for electric motor is a power transmission mechanism that uses a gear speed converter to decelerate
the number of revolutions of the motor (motor) to the required number of revolutions and obtain a
mechanism with a large torque. Product specifications: 40 ~ 250; Transmission ratio: single stage 10 ~ 60, double stage 200 ~ 900; Input power: single stage 0.12 ~ 33.20 kW (input speed 1500rpm); dual stage 0.12 ~ 17.71 kW; Output torque: single stage 6 ~ 6050N•m; double stage 63 ~ 6050 N•m. A total of more than 20,000 different specifications, transmission ratios, connections and installation methods
are available for 60 series to meet the various needs of users.

The basic structure of the Worm gearbox for electric motor: Mainly composed of transmission parts worm gear, shaft, bearing, box and its accessories. Can be divided
into three basic structural parts: box, worm gear, bearing and shaft combination. The box is the base of all
the accessories in the Worm gearbox for electric motor. It is an important part that supports the fixed shaft parts, ensures
the correct relative position of the transmission parts and supports the load acting on Worm gearbox for electric motor. The main
function of the worm gear is to transmit the motion and power between the two staggered shafts. The main
function of the bearing and the shaft is power transmission, operation and efficiency. Worm gear reduction and features: American technology, durable, smooth transmission, large carrying
capacity, low noise; compact structure, large transmission ratio; wide power source, motor or other power
drive. The accessories of the Worm gearbox for electric motor are explained as follows: Oil cap/ventilator, mainly used to discharge gas in the Worm gearbox for electric motor case; The end cover is divided into a large end cover and a small end cover. The end cover is an axial position of
the fixed shafting component and is subjected to an axial load, and both ends of the bearing seat hole are
closed by a bearing cover; Oil seal; mainly used to prevent the leakage of lubricating oil inside the chassis and improve the use time
of the lubricating oil; Oil drain plug, mainly used to discharge dirty oil and cleaning when replacing lubricating oil; The oil cap/oil mark is mainly used to observe whether the oil quantity inside the Worm gearbox for electric motor
chassis is up to standard; WP series Worm gearbox for electric motor products use the highest standards in the selection of materials and manufacturing
processes, such as the use of high-quality synthetic oil, imported brand-name seals, etc., finishing, refining,
precision assembly production. The utility model has the advantages of beautiful appearance, convenient
installation, compact structure, low noise and high efficiency.
Survive by quality, develop by word of mouth Production of eight series of more than 10,000 kinds of speed Worm gearbox for electric motor, covering metallurgy, stone, wood,
tobacco, food leather, textile, glass, medical, chemical, light industry, rubber, construction, marine and
other industries.

Working conditions:The worm speed of the WP Worm gearbox for electric motor in stockcannot exceed 1500r/min.The working environment temperature is -40 °C - +40 °C. When the working environment temperature is lower than 0 °C, the lubricating oil must be heated to above 0 °C before starting.

When the working environment temperature is higher than 40 °C, cooling measures must be taken. Sogears Motor manufactures helical type and worm type gear Worm gearbox for electric motor (gearboxes) for gearmotor. All of our worm gearbox for electric motor have excellent quality and power transmission applications. New worm gearbox for electric motor products manufacturing in China, with stylish and cool design emerge. For the new and latest worm gearbox for electric motor products in 2019 from credible China manufacturers, suppliers and factories. Contact most popular products of manufacturer from sogears.

The Worm gearbox for electric motor in stockcan be rotated in the positive and negative directions.Precautions:The worm gear shaft can never be used as an input shaft.The supporting motor (ie power) cannot exceed the value specified on the label.If the user wants to change the direction of the input shaft, the lower end cover of the lower shaft can be removed, the worm shaft can be taken out and the 180 can be adjusted. Just load it.

WP series worm gearbox for electric motors are used throughout the world in a variety of applications. Gear Worm gearbox for electric motors reduce speed and increase torque. WP series worm gearbox for electric motors are sometimes called speed Worm gearbox for electric motors, gear drives or gearboxes. There are different types of gear Worm gearbox for electric motor designs. You can find more details from us and contact us now.

Do not hard knock when installed, slowly drive the two shafts to make them engage. worm gearbox for electric motors Single Reduction Constructed with a high tensile strength cast bronze worm wheel and a hardened, ground alloy steel worm, integrated with the shaft to assure a long, trouble-free life. worm gearbox for electric motor Double Reduction Double reduction units are made with the same high quality components as the single reduction Worm gearbox for electric motors.

WP Worm gearbox for electric motor is developed on the basis of WD Worm gearbox for electric motor. The worm is made of 45# high-quality
steel by heat treatment. The worm wheel is made of tin bronze. The wear resistance is good, especially in
the bearing capacity. The Worm gearbox for electric motor is mainly used for the reduction transmission of various
mechanical equipments such as plastics, metallurgy, beverages, mining, lifting and transportation, and
chemical construction
Features: 1. The transmission is stable, the vibration, impact and noise are small, the reduction ratio is large, the
versatility is wide, and it can be used with various mechanical equipments.
2. It can obtain a large transmission ratio with single-stage transmission, and has a compact structure.
Most models have better self-locking performance, and can save braking device
3, worm screw and worm gear for mechanical equipment with braking requirements. The meshing friction
loss of the tooth surface is large, so the transmission efficiency is lower than that of the gear, and it is easy
to generate heat and high temperature.
4. Higher requirements for lubrication and cooling.
5, good interoperability, worm gears are manufactured according to national standards, bearings, oil seals,
etc. are used standard parts.
6, the box type has basic type and universal type

Details:

This product is a cylindrical Worm gearbox for electric motor in stockproduced according to the national standard “GB10085-88”.installation method: 1 base installation, 2 flange installation, 30,000 can be installed.Output mode: 1 solid shaft output, 2 hollow shaft output.

4, reduction ratio: 1 basic type (single stage) 1:10--1:60, 2 combination type (two-stage) up to 1:3600, 3 combination of three or more levels is larger.

5, motor power (input): 0.12KW--15KW

Low Input WP series worm gearbox for electric motor. About Sogears Company. Over Four Decades of Quality Manufacturing. Sogears Products has been manufacturing high quality WP series worm gearbox for electric motor for power transmission systems since 1975. Our WP series worm gearbox for electric motor include right angle, bevel, worm gear and spindle for various types of on and off-road. Our motors & Worm gearbox for electric motors may be purchased mechanically OK or E-OK or reconditioned with a WARRANTY. The best value is the WP series worm gearbox for electric motor. WP series worm gearbox for electric motor were purchased and never put into service. The savings on these items can be up to 70%. Used WP series worm gearbox for electric motor are also a great value.