English English

Products

Sumitomo type cyclo

Sumitomo type cyclo

sumitomo cyclo 4000, sumitomo cyclo 6000 price, sumitomo gearbox parts, cyclo drive motor, sumitomo gearbox catalog pdf, cyclo drive gear motor, sumitomo cyclo catalogue, sumitomo cyclo 6000 catalog pdf

The cycloidal pinwheel reducer is a novel transmission device using the principle of K-H-V less tooth difference planetary transmission. The transmission process is as follows: a double eccentric sleeve with a misalignment of 180 degrees is mounted on the input shaft, and two roller bearings called a jib are mounted on the eccentric sleeve to form an H mechanism, and the center holes of the two cycloidal wheels are eccentric The sleeve is loaded with the raceway of the arm bearing, and the cycloidal wheel and the needle gear are meshed to form an internal meshing speed reduction mechanism with a difference of one tooth.

This product is widely used in metallurgy, mining, lifting, transportation, cement, construction, chemical, printing and dyeing, pharmaceutical, food and environmental protection industries. Applicable to the working environment temperature of -40 ° C -40 ° C, under the rated load and speed, the oil tank temperature rise of the reducer does not exceed 60 ° C, the maximum oil temperature does not exceed 80 ° C.

sumitomo cyclo 6000 price

High-speed ratio and high-efficiency single-stage transmission can achieve a reduction ratio of 1:87, and the efficiency is above 90%. If multi-stage transmission is adopted, the reduction ratio is larger. The first-stage transmission reduction ratio is 9~87, the double-stage transmission reduction ratio is 121~5133, the multi-stage combination can reach tens of thousands, and the pin-tooth meshing-type rolling friction, the meshing surface has no relative sliding, so the first-stage deceleration efficiency is up to 94%.
Horizontal Sumitomo type cyclo pinwheel reducer is compact and small. Due to the planetary transmission principle, the input shaft output shaft is on the same axis, making the model as small as possible.
Smooth running noise Low Sumitomo type cyclo pin teeth have a large number of meshing teeth, a large overlap coefficient and a mechanism for balancing the components, so that vibration and hum are limited to a minimum.
The horizontal Sumitomo type cyclo has many pairs of teeth in contact during operation, large coincidence, stable operation, strong overload capability, low vibration and noise, and low noise of various specifications.Reliable use and long service life Because the main parts are made of bearing steel material, high strength is obtained by quenching treatment (HRC58~62), and some transmission contact adopts rolling friction, so it has long durability and long service life.

sumitomo cyclo 6000 pricesumitomo cyclo 6000 pricesumitomo cyclo 6000 pricesumitomo cyclo 6000 price
Because the main parts are made of bearing steel quenching treatment (HRC58-62), and then refined, and the Sumitomo type cyclo teeth and the toothed sleeves are meshed and transmitted to the teeth to form a rolling friction, the friction coefficient is small, so that the meshing area has no relative sliding. Extremely wear-resistant, so durable.
Reasonable design, easy maintenance, easy to disassemble and install, minimum number of parts and simple lubrication, so that the Sumitomo type cyclo pinwheel reducer is deeply trusted by users.
Compared with other reducers of the same power, the weight volume is less than 1/3. Because it is a planetary transmission, the input shaft and the output shaft are on the same axis to obtain the smallest possible size.

WB miniature Sumitomo type cyclo reducer (aluminum shell material, small power, small size)
product description:
WB series reducer is a kind of machine that realizes deceleration according to the principle of less tooth difference planetary transmission and Sumitomo type cycloal pin gear meshing. The machine is divided into horizontal, vertical, double-axis and direct-coupled assembly methods, which are ideal equipment for metallurgy, mining, construction, chemical, textile, light industry and other industries.
Performance characteristics:
1. WB miniature Sumitomo type cyclo reducer adopts high-speed ratio and high-efficiency single-stage transmission, which can achieve a reduction ratio of 1:87, and the efficiency is above 90%. If multi-stage transmission is adopted, the reduction ratio is larger.
2. The Sumitomo type cyclo reducer has a compact structure and small size. Due to the planetary transmission principle, the input shaft output shaft is on the same axis, which makes the model as small as possible.
3, smooth operation, low noise, Sumitomo type cycloal gear teeth, large number of teeth, large overlap coefficient and mechanism of machine balance, so that vibration and humming are limited to a minimum.
4. Reliable use and long service life Because the main parts are made of high-carbon chrome steel material, high strength is obtained by quenching treatment (HRC58~62), and some transmission contact adopts rolling friction, so it has long durability and long service life.
5, reasonable design, easy maintenance, easy to disassemble and install, the minimum number of parts and simple lubrication, so that the Sumitomo type cyclo reducer is deeply trusted by users.

sumitomo gearbox partssumitomo gearbox parts

technical parameter:

Power: 0.04KW ~ 3KW
Torque: 25N·m~250N·m
Transmission ratio: single stage: 9-87 two-stage: 121-1849
Basic model:
1. The single-stage reducer speed ratio models are WB65, WB85, WB100, WB120 and WB150;
   The reduction ratios are 9, 11, 17, 23, 29, 35, 43, 59, 71, 87, respectively.
2. The two-stage reduction ratio models are WBE1065, WBE1285 and WBE1510;
   The reduction ratios are 121, 187, 289, 385, 473, 595, 731, 989, 1225, 1849, etc.

cyclo drive motorcyclo drive motorsumitomo cyclo 6000 manual

8000 series Sumitomo type cyclo pinwheel reducer model
8000 Series XW, XWD Sumitomo type cyclo Pinwheel Reducer
8000 Series XL, XLD Sumitomo type cyclo Pinwheel Reducer
8000 Series XWE, XWED Sumitomo type cyclo Pinwheel Reducer
8000 series XLE, XLED type cycloid reducer

The 8000 series cycloid reducer is a kind of planetary gear transmission principle. It adopts Sumitomo type cyclo pin wheel meshing, and has advanced design and novel structure. In most cases, this type of reducer has replaced two-stage and three-stage ordinary cylindrical gear reducers and cylindrical worm reducers in military, aerospace, metallurgy, mining, petroleum, chemical, shipbuilding, light industry, food, textile, Printing, dyeing, pharmaceutical, rubber, plastics, and lifting and transportation are increasingly used.
Features
1. The transmission ratio is large. The gear ratio is 1/6–1/87 at the first stage of deceleration. The transmission ratio is 1/99–1/7569 for two-stage deceleration and 1/5841–1/658503 for three-stage transmission. In addition, multi-level combinations can be used as needed, and the speed ratio is as large as specified.
2. Transmission efficiency is high. Since the meshing portion uses rolling engagement, the first-stage transmission efficiency is generally 90%–95%.
3. Compact structure, small size and light weight. The volume can be reduced by 2/1–2/3 compared to conventional cylindrical gear reducers.
4. Less failure and long life. The main transmission meshing parts are manufactured by bearing steel grinding, so the mechanical properties and wear resistance are good, and because of the rolling friction, the failure is small and the service life is long.
5. Smooth and reliable operation. Because of the multi-tooth meshing during the transmission process, it is stable and reliable, and the noise is low.
6. Easy to disassemble and install, easy to repair.
7. Strong overload capability, impact resistance, small moment of inertia, suitable for frequent starting and reverse running.
cyclo drive motor

From the perspective of proper maintenance, we need to pay attention to the following six aspects:
 
(1) For parts that are more susceptible to corrosion in the equipment, such as shaft seals, it is easy to age and wear. During the operation of the Sumitomo type cyclo, the smoothness and sealing of the two contact parts can be ensured, and the noise generated by the operation can be reduced. Regular inspection and replacement of the shaft seal is required. In addition, the wear of the shaft seal can easily cause dust or some metal powder in the working environment to enter the inside of the Sumitomo type cyclo.
 
(2) When the operating temperature of the Sumitomo type cyclo exceeds the bearing use temperature, it is necessary to stop the inspection, and carefully check whether the bearing, the gear sleeve, the faceplate, the spacer ring, the pin sleeve and other parts of the Sumitomo type cyclo are damaged, if there is a certain degree of deformation or Damage, need to be replaced in time, and also pay attention to the correct installation when replacing.
 
(3) When the Sumitomo type cyclo is working normally, the eccentric bearing is stressed, and the eccentric bearing should be replaced in time for disassembly and repair.
 
(4) When the Sumitomo type cyclo is unsealed for maintenance inspection, the installation process must be cautious and careful. After wiping the contact surface, replace the gasket with a suitable thickness with a sealant.
 
(5) The different internal structure, parts and equipment parameters of different Sumitomo type cyclo models are different. The internal parts cannot be replaced at will, or they can be used together with other Sumitomo type cyclo parts.
 
Due to the different conditions, operating environment and running time of the Sumitomo type cyclo, various faults will occur during the actual operation. The installation, use and maintenance of the Sumitomo type cyclo require strict installation and operation standards. In addition, the relevant staff should pay more attention to the advantages of the cycloidal pinwheel Sumitomo type cyclo, and improve work efficiency.

 sumitomo cyclo 4000 sumitomo cyclo 4000

sumitomo gearbox catalog pdf

The Sumitomo type cyclo pinwheel reducer can match the speed regulating motor, brake motor, explosion-proof motor and ordinary Y series motor according to user requirements. According to the size of the reducer frame number, the motors of different powers can be matched, ranging from (0.04kw) to 75kw.
model
1) B series Sumitomo type cyclo pinwheel reducer 2) X series Sumitomo type cyclo pinwheel reducer
display method:
1) Single-stage transmission, the transmission ratio is 9-87B (X) W (L) D1-87-1.5B (X) - B series cycloid reducer;
    X series Sumitomo type cyclo pinwheel reducer. W(L) — W is a horizontal installation; L is a vertical installation. D (B) - D is configured with Y series ordinary motors; B is configured with YB series explosion-proof motors.
    1 — The model number of the base is 1.87 — the reduction ratio is 87. 1.5 — The motor power is 1.5kw.

2) Two-stage transmission, the transmission ratio is generally 121-7569B (X) W (L) ED185-473-16B (X) - B series cycloid reducer; X series cycloid reducer. W(L) — W is a horizontal installation; L is a vertical installation. E — E is a two-stage transmission. D(B)—D is the Y series ordinary motor; B is the YB series explosion-proof motor. 185 — The model number of the base is 185.473 — the reduction ratio is 473.16 The motor power is 16kw.
Conditions of use 1. The Sumitomo type cyclo pinwheel reducer is allowed to be used in continuous working mode, while allowing both forward and reverse directions. Some models of Sumitomo type cyclo reducers allow only one direction of rotation.
2. The rated speed of the input shaft is 1500 rpm. When the input power is greater than 18.5 kW, it is recommended to use a 6-pole motor with 960 rpm.
3. The working position of the horizontally mounted cycloid reducer is horizontal. The maximum horizontal tilt angle during installation is typically less than 15°. Other measures should be taken to ensure adequate lubrication and prevent oil leakage when it exceeds 15°.
4. The output shaft of the cycloid reducer cannot be subjected to large axial and radial forces. Other measures must be taken when there are large axial and radial forces.

sumitomo cyclo 6000 speed reducersumitomo cyclo 6000 speed reducer

Lubrication 1. The horizontal cycloid reducer is lubricated under normal conditions by oil pool. The height of the oil surface can be kept in the middle of the oil window. Cyclic lubrication can be used when the working conditions are bad and the ambient temperature is high.
2. The Sumitomo type cyclo pinwheel reducer is generally lubricated with 40# or 50# mechanical oil at normal temperature. In order to improve the performance of the reducer and prolong the service life, it is recommended to use 70# or 90# extreme pressure gear oil in high and low temperature conditions. Lubricants should also be reconsidered during work.
3. The vertical installation of the planetary cycloid reducer should strictly prevent the oil pump from breaking oil to avoid damage to the components of the reducer.
4. When refueling, you can rotate the vent cap on the upper part of the base to refuel. When draining oil, screw the oil drain plug on the lower part of the base to release the oil. The reducer is internally free of lubricant when it leaves the factory.
5, the first refueling operation for 100 hours should be replaced with new oil, (and the internal sewage is washed clean) and then continue to work, change every six months (8-hour work system), if the working conditions are bad, the oil change time can be shortened appropriately, Lubricating oil should always be replenished during use.6, the factory's reducer has been greased, replaced every six months.

sumitomo cyclo 6000 speed reducersumitomo cyclo 6000 speed reducer

Installation 1. It is not allowed to use the direct slamming method when attaching the coupling, pulley, sprocket and other joints on the output shaft of the cycloid reducer, because the output shaft structure of the reducer cannot withstand the axial slamming force. , the shaft end screw hole can be screwed into the coupling member.
2. The shaft diameter of the output shaft and the input shaft is matched with GB1568-79.
3. The lifting eye screw on the reducer is only used for lifting the reducer.
4. When installing the reducer on the basis, calibrate the installation centerline elevation of the reducer, the level and the relevant dimensions of the connected parts. The concentricity of the calibration drive shaft should not exceed the range allowed by the coupling.
5. When the speed reducer is calibrated, it can be carried out with steel blocks or cast iron blocks. The height of the blocks should not exceed three, and it can also be carried out with the iron. However, the gears should be replaced with flat blocks after calibration.
6. The arrangement of the blocks should avoid the deformation of the body. The two sides of the foundation bolts should be arranged symmetrically. The mutual distance can be enough to allow the water slurry to circulate freely during irrigation.
7. The irrigation of cement slurry should be dense, and there should be no air bubbles, voids and other defects. The term explains the reduction ratio: the ratio of the input speed to the output speed.

sumitomo cyclo 6000 manualsumitomo cyclo 6000 manual

Series: Number of sets of planetary gears. Generally, the maximum level can reach three, and the efficiency will be reduced.
Full load efficiency: The transmission efficiency of the reducer under the maximum load condition (fault stop output torque).
Working life: The cumulative working time of the reducer under rated load and rated input speed.
Rated torque: It is the long-running torque allowed for the rated life. When the output speed is 100 rpm, the life of the reducer is the average life. When this value is exceeded, the average life of the reducer will decrease. The gear unit fails when the output torque exceeds twice. Noise: unit decibel, this value is the input speed of 3000 rev / min, without load, measured at a distance of 1 m from the reducer. Hysteresis: The input end is fixed, the output end rotates clockwise and counterclockwise. When the output end is subjected to positive and negative 2% rated torque, the output end of the reducer is displaced by a slight angular displacement, which is the return gap.
The following are some of the gear ratios listed: single-stage gear ratio: 9, 11, 17, 23, 29, 35, 43, 59, 71, 87
Two-stage transmission ratio: 121 (11 × 11), 187 (17 × 11), 253 (23 × 11), 289 (17 × 17), 385 (35 × 11), 391 (23 × 17), 473 (43 ×11), 493 (29×17), 595 (35×17), 731 (43×17), etc.

sumitomo cyclo 6000 manualsumitomo cyclo 6000 manual

Torque calculation Cycloid reducer torque = 9550 × motor power ÷ motor power input speed × speed ratio × use efficiency (65% - 75%) common fault reducer in the long-term operation, often wear, leakage and other faults ,

The most important ones are: 1. The bearing chamber of the reducer is worn, including the wear of the bearing housing, the bearing housing inside the housing, and the bearing housing of the transmission.
2. The shaft diameter of the gear shaft of the reducer is worn, and the main wear parts are in the shaft head, keyway, etc.
3. Bearing wear of the drive shaft of the reducer
4, the reducer combined surface leakage heat cause If the Sumitomo type cyclo pinwheel reducer is in use, the temperature is too high, generally divided into the following possibilities:
     1). This may be a problem with the eccentric bearing and there is a malfunction.
     2). If the reducer is often overloaded, the temperature will be too high.
     3). The reducer lacks lubricant,
    4). If the newly purchased machine may be assembled with unreasonable conditions, there may be problems.

Technical parameters: Power: 0.37KW~55KW Torque: 150N·m~20000N·m Transmission ratio: Single stage: 9-87 Two stages: 121-7569 Level 3: 2057-658503

Date

23 January 2015

Tags

Cycloidal gear , Cycloidal Gear Motor

 Geared Motors And Electric Motor Manufacturer

The best service from our transmission drive expert to your inbox directly.

Get in Touch

Yantai Bonway Manufacturer Co.ltd

ANo.160 Changjiang Road, Yantai, Shandong, China(264006)

T+86 535 6330966

W+86 185 63806647

© 2024 Sogears. All Rights Reserved.